Your car radiator is the primary cooling mechanism for your engine. Parts train's Radiators are a simple and elegant solution to the need for engine cooling. Parts train's Radiators are mostly made of aluminum. Light and strong, aluminum is great for making radiators. It is the material of choice for most of today’s radiators. Light and intelligently designed, aluminum radiators are standard on many of today’s new cars and trucks.
A small leak on your Radiator can be indicating a larger problem. A cooling system that runs low too often is less efficient and you can damage your cooling system by letting the coolant level get too low. Too little coolant flow can be bad, but at normal and high operating temperatures, the rate at which coolant moves through the radiator does not change the amount of heat that is dissipated by the cooling cores. The amount of cooling will not be reduced even when the mean temperature of the coolant rises and flows faster.
Many cheap coolants do not have the corrosion protection, PH balancing, or sediment prevention that the top-quality coolants do. These low quality coolants do not have the same additives of name brand coolants. To help your engine stay cooler, rev up your engine slightly when you are overheating in traffic to help push more air across the cooling cores and more coolant through the engine.
All water-cooled radiators have an automatically controlled electric fan on the radiator. The way the system is supposed to work is that, after the engine is started, the thermostat on the engine stays closed until the coolant temperature at the ENGINE reaches 87C (189F) degrees. It is the responsibility of the Radiator to keep the coolant temperature from running too high. However, if the temperature is too high it is not necessarily the radiator.
A poor radiator cap will not last as long or stay properly calibrated, and either open at too low or two high a pressure. Make sure your radiator cap is the proper one for your cooling system. Higher pressure means a higher boiling point, which means more efficient cooling. A new radiator cap is usually all that is required for this (but don’t over pressurize your radiator cores and wreck the whole system).
Most Radiators' cooling system failures arise from poor radiator maintenance. Many radiator problems can be prevented with regular maintenance and periodic professional inspections of you car radiator and cooling system. The most common radiator problems are: leaky fittings or seams, fin deterioration and bond failure, electrolysis, cracked tank, and fan damage.
Parts train's Aftermarket Parts, Replacement Parts and top grade Radiators are reasonably priced and the company makes sure they are durable. Parts train offers Volvo parts focused on reliability, quality, great designs and affordable price. With the Volvo tradition of designing efficient and innovative cars, Parts train has in its stock the widest array as well high standard Volvo Parts, Performance Parts, and Replacement Parts.
With only a few clicks, visit http://www.partstrain.com/ShopByVehicle/VOLVO and you will find Parts train's impressive array of highly durable and reliable Volvo Parts to match the equally impressive performance of your Volvo.
Tuesday, August 2, 2011
Saturday, June 4, 2011
Tips for maintaining your Snowblower
If you don't want to be standing out in the cold arguing with a snowblower that doesn't want to run, then do the annual maintenance before the snow starts flying. Regular maintenance will give you years of hassle free use, and less attitude from your blower. Don't forget the safety aspect, because without proper maintenance your snowblower could become a hazard.
Each fall before winter arrives, you should check all bolts, belts, and moving parts, to ensure they are not frayed, loose, or worn. Belts are best checked by removing and checking for cracks. Replace any worn parts, and tighten any loose bolts.
Turn your snowblower on its side and check the scraper bar. This is the bar that rubs against the ground and scrapes the snow off. This item wears, so check to see if it need replacement. If you neglect to replace the bar when it is worn, it will lead to damage on the snowblower's housing, and that's will hurt your pocket book. In fact, if your snowblower gets a lot of use through out the season, check it regularly.
Check the rubber paddles and the rubber on the auger. If your finger fits between the rubber and the housing it's time to replace the rubber. A new rubber will help your snowblower operate at its optimum performance levels.
Check tires for wear and proper inflation. Adjust as needed. If you have tire chains for your snowblower, have them handy or put them on in advance. There's nothing worse than searching in the freezing cold, while trying to remember where you put the chains.
There are only two types of snow blower engines: The two cylinder engine which uses mixed gas and oil. You'll just need to replace the spark plug on this style of engine.
If you have a four cylinder engine which uses straight gas, with the oil in the crank case just like your vehicle, you'll need to change the oil, spark plug, and filter. You should also check the oil each time before you start it. Most four cylinders use 5W30 oil, and hold approx 20 ounces. Refer to your owner's manual for the correct oil weight, and replacement part numbers.
Lube the drive and chassis. If you have two stage blower, make sure you check the lube in the gear box. Check with your owners manual whether you have a one stage or two stage. It will also tell you the type of lubricant to use.
If there was fuel left from the previous year, you'll need to siphon it off, and fill the gas tank with fresh gasoline. It doesn't hurt to add some methanol in with the fuel, once or twice a season, to avoid condensation from building up in the tank, or the carburetor icing up.
Each fall before winter arrives, you should check all bolts, belts, and moving parts, to ensure they are not frayed, loose, or worn. Belts are best checked by removing and checking for cracks. Replace any worn parts, and tighten any loose bolts.
Turn your snowblower on its side and check the scraper bar. This is the bar that rubs against the ground and scrapes the snow off. This item wears, so check to see if it need replacement. If you neglect to replace the bar when it is worn, it will lead to damage on the snowblower's housing, and that's will hurt your pocket book. In fact, if your snowblower gets a lot of use through out the season, check it regularly.
Check the rubber paddles and the rubber on the auger. If your finger fits between the rubber and the housing it's time to replace the rubber. A new rubber will help your snowblower operate at its optimum performance levels.
Check tires for wear and proper inflation. Adjust as needed. If you have tire chains for your snowblower, have them handy or put them on in advance. There's nothing worse than searching in the freezing cold, while trying to remember where you put the chains.
There are only two types of snow blower engines: The two cylinder engine which uses mixed gas and oil. You'll just need to replace the spark plug on this style of engine.
If you have a four cylinder engine which uses straight gas, with the oil in the crank case just like your vehicle, you'll need to change the oil, spark plug, and filter. You should also check the oil each time before you start it. Most four cylinders use 5W30 oil, and hold approx 20 ounces. Refer to your owner's manual for the correct oil weight, and replacement part numbers.
Lube the drive and chassis. If you have two stage blower, make sure you check the lube in the gear box. Check with your owners manual whether you have a one stage or two stage. It will also tell you the type of lubricant to use.
If there was fuel left from the previous year, you'll need to siphon it off, and fill the gas tank with fresh gasoline. It doesn't hurt to add some methanol in with the fuel, once or twice a season, to avoid condensation from building up in the tank, or the carburetor icing up.
Perform Your Own Automobile Maintenance
Today’s cars can typically be expected to pass the 200,000 mile mark with consistent automobile maintenance. With the price of automobiles, you will want to protect that investment by performing regular maintenance. If you can do much of the work yourself, you will save a lot of money in labor. Invest in a good set of tools and choose quality parts when performing your own automobile maintenance.
If you have some skill, but want to learn more look for courses in general repairs and maintenance. These can often be found at your local community center, Community College or an automotive technical school in your area. Consider investing in a good repair manual for your car, such as a Chilton’s manual. The internet is a good place to look for articles and information. There are many sites devoted to auto repair and maintenance.
You will want to keep track of all maintenance performed on your car. You can do this in a log, a notebook or on your home computer. There is software available to help you keep track of maintenance. These programs track repairs, maintenance, replacement parts used on the vehicle and fuel consumption. You can use the same software for multiple vehicles.
Most software allows you to create a service schedule and will remind you when it’s time to perform maintenance tasks on each vehicle in your household. The software contains a wide variety of tips for car care. In addition, many have reference and diagnostic tools to help you diagnose various problems with your cars. Many companies offer a free trial that can be downloaded on the internet. This allows you to try out the program before investing your money.
Your owner’s manual will give you some basic information about when certain maintenance tasks should be done. Most tasks will be listed according to the mileage on the car.
3000 Mile Maintenance
Change the oil in your engine every 3000 miles. The filter should be changed at the same time. Newer synthetic oils are said to last longer without breaking down. When you change the oil, check the fluids, the air filter, tires, hoses and belts. At this time check the battery cables and terminals for corrosion. This can be removed with a wire brush or sandpaper.
5000-10,000 Miles:
Have your tires rotated and balanced every five to ten thousand miles. This helps the tires wear evenly and extends the life. The best tires should be put in the front of the car. Check the tire pressure regularly and check the tread for signs of uneven wear or damage.
15,000 Miles:
Change the air filter every 15,000 miles. A clean air filter improves the fuel economy of your car. A dirty air filter can cause the engine to run rough and stall. At this time you should also check the pads and shoes on your brake system. Check the brake fluid and top it of, as needed. The fluid should be clear. If you notice noise when the brakes are applied or the steering wheel shakes or vibrates, this can be an indication that the brakes need replacing. In this case, don’t wait check the brakes and replace as needed.
30,000 Miles:
Check the fluid level on your transmission. The owner’s manual will have information about the kind of fluid that should be used in your car. The manual should have directions on how to drain and replace the fluid. The pan gasket should be changed when the fluid is drained. Also at this time, give the car a tune up. Replace all spark plugs and wires.
50,000 Miles:
Change the coolant at 50,000 miles. See the owner’s manual for directions on how to perform this task.
Remember to take care of your car’s finish. You want the paint to remain in good condition for as long as possible. Wash the car regularly, even in the winter when salt from the roads can ruin the finish. Apply wax to protect the paint from the sun, salt and weather conditions. Don’t neglect the headlights, which can become cloudy and won’t operate as well. New Lite Headlight Cleaner and Restorer will return cloudy headlights to like new condition. Learn more about this product at http://www.mdwholesale.com
Subscribe to:
Posts (Atom)